smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p16 amd64] (local build) Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HGST HDN724030ALE640 Serial Number: PK2234P9J0675Y LU WWN Device Id: 5 000cca 248dc4666 Firmware Version: MJ8OA5E0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Aug 14 13:15:51 2015 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 448) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 86 3 Spin_Up_Time 0x0007 209 209 024 Pre-fail Always - 360 (Average 236) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 21 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 119 119 020 Pre-fail Offline - 35 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 127 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 13 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 23 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 23 194 Temperature_Celsius 0x0002 176 176 000 Old_age Always - 34 (Min/Max 25/46) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 106 SMART Error Log Version: 1 ATA Error Count: 106 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 106 occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 a0 38 59 48 02 Error: ICRC, ABRT at LBA = 0x02485938 = 38295864 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 f0 08 e8 58 48 40 00 00:09:45.863 WRITE FPDMA QUEUED 60 10 00 90 9e 50 40 00 00:09:45.863 READ FPDMA QUEUED 61 f0 00 f8 57 48 40 00 00:09:45.775 WRITE FPDMA QUEUED ef 10 02 00 00 00 00 00 00:09:45.528 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 00:09:45.528 SET FEATURES [Enable write cache] Error 105 occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 c8 98 52 48 02 Error: ICRC, ABRT at LBA = 0x02485298 = 38294168 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 d8 00 88 52 48 40 00 00:09:44.530 WRITE FPDMA QUEUED ef 10 02 00 00 00 00 00 00:09:44.283 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 00:09:44.283 SET FEATURES [Enable write cache] ef aa 00 00 00 00 00 00 00:09:44.283 SET FEATURES [Enable read look-ahead] ef 03 46 00 00 00 00 00 00:09:44.283 SET FEATURES [Set transfer mode] Error 104 occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 78 e8 52 48 02 Error: ICRC, ABRT at LBA = 0x024852e8 = 38294248 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 d8 08 88 52 48 40 00 00:09:43.800 WRITE FPDMA QUEUED 60 10 00 90 02 40 40 00 00:09:43.800 READ FPDMA QUEUED 61 80 08 d8 dc 5b 40 00 00:09:43.723 WRITE FPDMA QUEUED 61 d0 00 88 4f 48 40 00 00:09:43.723 WRITE FPDMA QUEUED ef 10 02 00 00 00 00 00 00:09:43.631 SET FEATURES [Enable SATA feature] Error 103 occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 28 18 6e 55 04 Error: ICRC, ABRT at LBA = 0x04556e18 = 72707608 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 48 08 f8 6d 55 40 00 00:09:39.886 WRITE FPDMA QUEUED 60 08 00 70 a2 50 40 00 00:09:39.886 READ FPDMA QUEUED 61 f0 00 d8 6c 55 40 00 00:09:39.798 WRITE FPDMA QUEUED ef 10 02 00 00 00 00 00 00:09:39.760 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 00:09:39.760 SET FEATURES [Enable write cache] Error 102 occurred at disk power-on lifetime: 127 hours (5 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 60 20 3a 5b 02 Error: ICRC, ABRT at LBA = 0x025b3a20 = 39533088 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 80 58 28 3f 5b 40 00 00:09:36.314 WRITE FPDMA QUEUED 61 80 50 a0 3e 5b 40 00 00:09:36.314 WRITE FPDMA QUEUED 61 80 48 20 3e 5b 40 00 00:09:36.314 WRITE FPDMA QUEUED 61 80 40 18 3d 5b 40 00 00:09:36.314 WRITE FPDMA QUEUED 61 18 38 70 26 f0 40 00 00:09:36.314 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.