Adapter #0 ============================================================================== Versions ================ Product Name : LSI MegaRAID SAS PCI Express ROMB Serial No : FW Package Build: 12.13.0-0171 Mfg. Data ================ Mfg. Date : 00/00/00 Rework Date : 00/00/00 Revision No : Battery FRU : N/A Image Versions in Flash: ================ FW Version : 2.130.383-2618 BIOS Version : 3.28.00_4.14.05.00_0x05270000 Preboot CLI Version: 04.04-020:#%00009 WebBIOS Version : 6.0-52-e_48-Rel NVDATA Version : 2.09.03-0045 Boot Block Version : 2.02.00.00-0000 BOOT Version : 09.250.01.219 Pending Images in Flash ================ None PCI Info ================ Controller Id : 0000 Vendor Id : 1000 Device Id : 0079 SubVendorId : 1043 SubDeviceId : 8480 Host Interface : PCIE ChipRevision : B4 Link Speed : 0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 500e01800015d77f 1 0000000000000000 2 0000000000000000 3 0000000000000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 5000ea6270007550 BBU : Absent Alarm : Present NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 512MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Absent Temperature sensor for controller : Absent Settings ================ Current Time : 11:28:26 10/30, 2019 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 4 Delay Among Spinup Groups : 2s Physical Drive Coercion Mode : 1GB Cluster Mode : Disabled Alarm : Enabled Auto Rebuild : Enabled Battery Warning : Disabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Disabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 120 Auto Enhanced Import : No Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No POST delay : 90 seconds BIOS Error Handling : Stop On Errors Current Boot Mode :Normal Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Mix of SAS/SATA of HDD type in VD Allowed Mix of SAS/SATA of SSD type in VD Allowed Mix of SSD/HDD in VD Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 80 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 16 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 0 MB Device Present ================ Virtual Drives : 0 Degraded : 0 Offline : 0 Physical Devices : 4 Disks : 2 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : Yes Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : No Support Boot Time PFK Change : No Disable Online PFK Change : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : No Block SSD Write Disk Cache Change: No Support Online FW Update : Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : Yes Support Breakmirror : No Power Savings : No Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes NCQ : No Disable Copyback : No Enable : Yes Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Enable Spin Down of UnConfigured Drives : Yes Disable Spin Down of hot spares : No Spin Down time : 30 T10 Power State : No Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Enabled Cached IO : Yes SMART Mode : Mode 6 Alarm Disable : Yes Coercion Mode : 1GB ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : 0 Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : Yes Allow SSD SAS/SATA Mix in VD : Yes Allow HDD/SSD Mix in VD : Yes Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : Yes Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : No Disable Puncturing : No Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : Yes LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : Yes Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : Don't Auto spin down Configured Drives Max power savings option is not allowed for LDs. Only T10 power conditions are to be used. Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : No BreakMirror RAID Support : No Disable Join Mirror : No Enable Shield State : No Time taken to detect CME : 60s Exit Code: 0x00